Grades & Technical Data

Mechanical Properties & Chemical Composition

Name: Jagdamba Procut Pvt. Ltd.
Address: 504/1A GIDC Makarpura, Vadodara, Gujarat, 390010, IN
Telephone: +918799617251

Grade-wise reference values reproduced from our own material data sheets. Always verify against the latest standard edition and the order's MTC / TC.

Request Material for a Grade

Search & Filter

Find a grade

Grade	Standard	Yield Strength	Tensile Strength	Elongation	Impact / Condition
IS 2062 E250A	IS 2062:2011	250 / 240 / 230 MPa (t <20 / 20-40 / >40 mm)	≥ 410 MPa	≥ 23%	Not specified
IS 2062 E250BR	IS 2062:2011	250 / 240 / 230 MPa	≥ 410 MPa	≥ 23%	27 J @ RT, if specified
IS 2062 E250C	IS 2062:2011	250 / 240 / 230 MPa	≥ 410 MPa	≥ 23%	27 J @ -20°C
IS 2062 E350A	IS 2062:2011	350 / 330 / 320 MPa	≥ 490 MPa	≥ 22%	Not specified
IS 2062 E350BR	IS 2062:2011	350 / 330 / 320 MPa	≥ 490 MPa	≥ 22%	27 J @ RT, if specified
IS 2062 E350C	IS 2062:2011	350 / 330 / 320 MPa	≥ 490 MPa	≥ 22%	27 J @ -20°C
IS 2062 E450A	IS 2062:2011	450 / 430 / 420 MPa	≥ 570 MPa	≥ 20%	Not specified
IS 2062 E450BR	IS 2062:2011	450 / 430 / 420 MPa	≥ 570 MPa	≥ 20%	20 J @ RT, if specified
S355JR	EN 10025-2	≥ 355 MPa*	470-630 MPa*	≥ 20%*	27 J @ +20°C
S355J0	EN 10025-2	≥ 355 MPa*	470-630 MPa*	≥ 20%*	27 J @ 0°C
S355J2 / +N	EN 10025-2	≥ 355 MPa*	470-630 MPa*	≥ 20%*	27 J @ -20°C
ST52-3	Legacy DIN structural grade	Reference: ≥ 355 MPa	Reference: 490-630 MPa	As per standard	As per order
C45	EN 10083-2	Not applicable (supply condition dependent)	700-850 MPa**	≥ 14%**	Q&T; ref. t ≤ 16 mm
EN19	BS 970 (EN series)	As per heat treatment condition	As per heat treatment condition	As per standard	As per order
SA516 Gr. 60	ASME SA-516 / SA-516M	≥ 220 MPa	415-550 MPa	≥ 25%***	Impact by PO / supplement
SA516 Gr. 65	ASME SA-516 / SA-516M	≥ 240 MPa	450-585 MPa	≥ 23%***	Impact by PO / supplement
SA516 Gr. 70	ASME SA-516 / SA-516M	≥ 260 MPa	485-620 MPa	≥ 21%***	Impact by PO / supplement
Hardox 400 / 500	Wear-resistant plate	As per manufacturer data sheet	As per manufacturer data sheet	As per manufacturer data sheet	As per manufacturer data sheet
NM 400 / 500	Wear-resistant plate	As per manufacturer data sheet	As per manufacturer data sheet	As per manufacturer data sheet	As per manufacturer data sheet
690QL	High-strength quenched & tempered plate	As per manufacturer data sheet	As per manufacturer data sheet	As per manufacturer data sheet	As per manufacturer data sheet

Chemical Composition

Ladle / heat analysis reference

All values are % by mass unless otherwise stated.

Grade	C Max	Mn Max	Si Max	P Max	S Max	CE Max
IS 2062 E250A	0.23	1.50	0.40	0.045	0.045	0.42
IS 2062 E250BR	0.22	1.50	0.40	0.045	0.045	0.41
IS 2062 E250C	0.20	1.50	0.40	0.040	0.040	0.39
IS 2062 E350A	0.20	1.55	0.45	0.045	0.045	0.47
IS 2062 E350BR	0.20	1.55	0.45	0.045	0.045	0.47
IS 2062 E350C	0.20	1.55	0.45	0.040	0.040	0.45
IS 2062 E450A	0.22	1.65	0.45	0.045	0.045	0.52
IS 2062 E450BR	0.22	1.65	0.45	0.045	0.045	0.52
S355JR	≤0.24*	≤1.60	≤0.55	≤0.035	≤0.035	—
S355J0	≤0.24*	≤1.60	≤0.55	≤0.035	≤0.035	—
S355J2 / +N	≤0.24*	≤1.60	≤0.55	≤0.035	≤0.035	—
C45	0.42-0.50	0.50-0.80	≤0.40	≤0.045	≤0.045	—
SA516 Gr. 60	0.23**	0.85-1.20	0.15-0.40	≤0.025	≤0.025	—
SA516 Gr. 65	0.26**	0.85-1.20	0.15-0.40	≤0.025	≤0.025	—
SA516 Gr. 70	0.28**	0.85-1.20	0.15-0.40	≤0.025	≤0.025	—

Reference & Usage Notes

* S355 values shown for common plate thickness range; yield / tensile / elongation vary with thickness.
** C45 / SA516 carbon maximum shown as a representative reference; exact value varies by thickness.
*** SA516 elongation shown for 50 mm gauge length. Impact testing is supplementary unless specifically ordered.
Technical references: IS 2062:2011, EN 10025-2, EN 10083-2 and ASME SA-516 / SA-516M. Always verify against the latest standard edition and the order's MTC / TC.